Network Working Group M. Rose, Editor Request for Comments: 1158 Performance Systems International May 1990 Management Information Base for Network Management of TCP/IP-based internets: MIB-II 1. Status of this Memo This memo defines the second version of the Management Information Base (MIB-II) for use with network management protocols in TCP/IP- based internets. In particular, together with its companion memos which describe the structure of management information (RFC 1155) along with the network management protocol (RFC 1157) for TCP/IP- based internets, these documents provide a simple, workable architecture and system for managing TCP/IP-based internets and in particular the Internet community. This document on MIB-II incorporates all of the technical content of RFC 1156 on MIB-I and extends it, without loss of compatibilty. However, MIB-I as described in RFC 1156 is full Standard Protocol of the Internet, while the MIB-II described here is Proposed Standard Protocol of the Internet. This memo defines a mandatory extension to the base MIB (RFC 1156) and is a Proposed Standard for the Internet community. The extensions described here are currently Elective, but when they become a standard, they will have the same status as RFC 1156, that is, Recommended. The Internet Activities Board recommends that all IP and TCP implementations be network manageable. This implies implementation of the Internet MIB (RFC 1156 and the extensions in RFC 1158) and at least one of the two recommended management protocols SNMP (RFC 1157) or CMOT (RFC 1095). This version of the MIB specification, MIB-II, is an incremental refinement of MIB-I. As such, it has been designed according to two criteria: first, changes have been made in response to new operational requirements in the Internet; and, second, the changes are entirely upwards compatible in order to minimize impact on the network as the managed nodes in the Internet transition from MIB-I to MIB-II. It is expected that additional MIB groups and variables will be defined over time to accommodate the monitoring and control needs of new or changing components of the Internet. IETF SNMP Working Group [Page 1] RFC 1158 MIB II May 1990 Please refer to the latest edition of the "IAB Official Protocol Standards" RFC for current information on the state and status of standard Internet protocols. Distribution of this memo is unlimited. Table of Contents 1. Status of this Memo .................................. 1 2. Introduction ......................................... 3 3. Changes from MIB-I ................................... 4 3.1 Deprecated Objects .................................. 4 3.2 Display Strings ..................................... 5 3.3 The System Group .................................... 5 3.4 The Interfaces Group ................................ 5 3.5 The Address Translation Group ....................... 6 3.6 The IP Group ........................................ 7 3.7 The ICMP Group ...................................... 7 3.8 The TCP Group ....................................... 7 3.9 The UDP Group ....................................... 7 3.10 The EGP Group ...................................... 8 3.11 The Transmission Group ............................. 8 3.12 The SNMP Group ..................................... 8 4. Objects .............................................. 8 4.1 Object Groups ....................................... 9 4.2 Format of Definitions ............................... 10 5. Object Definitions ................................... 10 5.1 The System Group .................................... 11 5.2 The Interfaces Group ................................ 14 5.2.1 The Interfaces table .............................. 15 5.3 The Address Translation Group ....................... 27 5.4 The IP Group ........................................ 30 5.4.1 The IP Address table .............................. 38 5.4.2 The IP Routing table .............................. 41 5.4.3 The IP Address Translation table .................. 48 5.5 The ICMP Group ...................................... 51 5.6 The TCP Group ....................................... 61 5.6.1 The TCP Connection table .......................... 66 5.6.2 Additional TCP Objects ............................ 69 5.7 The UDP Group ....................................... 70 5.7.1 The UDP Listener table ............................ 72 5.8 The EGP Group ....................................... 73 5.8.1 The EGP Neighbor table ............................ 75 5.8.2 Additional EGP variables .......................... 83 5.9 The Transmission Group .............................. 83 5.10 The SNMP Group ..................................... 83 6. Definitions .......................................... 95 IETF SNMP Working Group [Page 2] RFC 1158 MIB II May 1990 7. Identification of OBJECT instances for use with the SNMP ................................................. 126 7.1 ifTable Object Type Names ........................... 127 7.2 atTable Object Type Names ........................... 127 7.3 ipAddrTable Object Type Names ....................... 128 7.4 ipRoutingTable Object Type Names .................... 128 7.5 ipNetToMediaTable Object Type Names ................. 129 7.6 tcpConnTable Object Type Names ...................... 129 7.7 udpTable Object Type Names .......................... 130 7.8 egpNeighTable Object Type Names ..................... 130 8. Acknowledgements .................................... 130 9. References .......................................... 131 10. Security Considerations.............................. 133 11. Author's Address..................................... 133 2. Introduction As reported in RFC 1052, IAB Recommendations for the Development of Internet Network Management Standards [1], a two-prong strategy for network management of TCP/IP-based internets was undertaken. In the short-term, the Simple Network Management Protocol (SNMP) was to be used to manage nodes in the Internet community. In the long-term, the use of the OSI network management framework was to be examined. Two documents were produced to define the management information: RFC 1065, which defined the Structure of Management Information (SMI) [2], and RFC 1066, which defined the Management Information Base (MIB) [3]. Both of these documents were designed so as to be compatible with both the SNMP and the OSI network management framework. This strategy was quite successful in the short-term: Internet-based network management technology was fielded, by both the research and commercial communities, within a few months. As a result of this, portions of the Internet community became network manageable in a timely fashion. As reported in RFC 1109, Report of the Second Ad Hoc Network Management Review Group [4], the requirements of the SNMP and the OSI network management frameworks were more different than anticipated. As such, the requirement for compatibility between the SMI/MIB and both frameworks was suspended. This action permitted the operational network management framework, the SNMP, to respond to new operational needs in the Internet community by producing this document. As such, the current network management framework for TCP/IP- based internets consists of: Structure and Identification of IETF SNMP Working Group [Page 3] RFC 1158 MIB II May 1990 Management Information for TCP/IP-based internets, RFC 1155 [13], which describes how managed objects contained in the MIB are defined; Management Information Base for Network Management of TCP/IP-based internets (version 2), this memo, which describes the managed objects contained in the MIB; and, the Simple Network Management Protocol, RFC 1157 [14], which defines the protocol used to manage these objects. Consistent with the IAB directive to produce simple, workable systems in the short-term, the list ofc objects (e.g., for BSD UNIX) were excluded. 7) It was agreed to avoid heavily instrumenting critical sections of code. The general guideline was one counter per critical section per layer. 3. Changes from MIB-I Features of this MIB include: 1) incremental additions to reflect new operational requirements; 2) upwards compatibility with the SMI/MIB and the SNMP; 3) improved support for multi-protocol entities; and, 4) textual clean-up of the MIB to improve clarity and readability. The objects defined in MIB-II have the OBJECT IDENTIFIER prefix: mib-2 OBJECT IDENTIFIER ::= { mgmt 1 } 3.1. Deprecated Objects In order to better prepare implementors for future changes in the MIB, a new term "deprecated" may be used when describing an object. A deprecated object in the MIB is one which must be supported, but one which will most likely be removed from the next version of the MIB (e.g., MIB-III). MIB-II marks one object as being deprecated: atTable As a result of deprecating the atTable object, the entire Address Translation group is deprecated. IETF SNMP Working Group [Page 4] RFC 1158 MIB II May 1990 Note that no functionality is lost with the deprecation of these objects: new objects providing equivalent or superior functionality are defined in MIB-II. 3.2. Display Strings In the past, there have been misinterpretations of the MIB as to when a string of octets should contain printable characters, meant to be displayed to a human. As a textual convention in the MIB, the datatype DisplayString ::= OCTET STRING is introduced. A DisplayString is restricted to the NVT ASCII character set, as defined in pages 10-11 of [7]. The following objects are now defined in terms of DisplayString: sysDescr ifDescr It should be noted that this change has no effect on either the syntax nor semantics of these objects. The use of the DisplayString notation is merely an artifact of the explanatory method used in MIB-II and future MIBs. Further, it should be noted that any object defined in terms of OCTET STRING may contain arbitrary binary data, in which each octet may take any value from 0 to 255 (decimal). 3.3. The System Group Four new objects are added to this group: sysContact sysName sysLocation sysServices These provide contact, administrative, location, and service information regarding the managed node. 3.4. The Interfaces Group The definition of the ifNumber object was incorrect, as it required all interfaces to support IP. (For example, devices without IP, such as MAC-layer bridges, could not be managed if this definition was strictly followed.) The description of the ifNumber object is changed IETF SNMP Working Group [Page 5] RFC 1158 MIB II May 1990 accordingly. The ifTable object was mistaken marked as read-write, it has been (correctly) re-designated as read-only. In addition, several new values have been added to the ifType column in the ifTable object: ppp(23) softwareLoopback(24) eon(25) ethernet-3Mbit(26) nsip(27) slip(28) Finally, a new column has been added to the ifTable object: ifSpecific which provides information about information specific to the media being used to realize the interface. 3.5. The Address Translation Group In MIB-I, this group contained a table which permitted mappings from network addresses (e.g., IP addresses) to physical addresses (e.g., MAC addresses). Experience has shown that efficient implementations of this table make two assumptions: a single network protocol environment, and mappings occur only from network address to physical address. The need to support multi-protocol nodes (e.g., those with both the IP and CLNP active), and the need to support the inverse mapping (e.g., for ES-IS), have invalidated both of these assumptions. As such, the atTable object is declared deprecated. In order to meet both the multi-protocol and inverse mapping requirements, MIB-II and its successors will allocate up to two address translation tables inside each network protocol group. That is, the IP group will contain one address translation table, for going from IP addresses to physical addresses. Similarly, when a document defining MIB objects for the CLNP is produced (e.g., [8]), it will contain two tables, for mappings in both directions, as this is required for full functionality. It should be noted that the choice of two tables (one for each direction of mapping) provides for ease of implementation in many cases, and does not introduce undue burden on implementations which realize the address translation abstraction through a single internal table. IETF SNMP Working Group [Page 6] RFC 1158 MIB II May 1990 3.6. The IP Group The access attribute of the variable ipForwarding has been changed from read-only to read-write. In addition, there is a new column to the ipAddrTable object, ipAdEntReasmMaxSize which keeps track of the largest IP datagram that can be re- assembled on a particular interface. There is also a new column in the ipRoutingTable object, ipRouteMask which is used for IP routing subsystems that support arbitrary subnet masks. One new object is added to the IP group: ipNetToMediaTable which is the address translation table for the IP group (providing identical functionality to the now deprecated atTable in the address translation group). 3.7. The ICMP Group There are no changes to this group. 3.8. The TCP Group Two new variables are added: tcpInErrs tcpOutRsts which keep track of the number of incoming TCP segments in error and the number of resets generated by a TCP. 3.9. The UDP Group A new table: udpTable is added. IETF SNMP Working Group [Page 7] RFC 1158 MIB II May 1990 3.10. The EGP Group Experience has indicated a need for additional objects that are useful in EGP monitoring. In addition to making several additions to the egpNeighborTable object, a new variable is added: egpAs which gives the autonomous system associated with this EGP entity. 3.11. The Transmission Group MIB-I was lacking in that it did not distinguish between different types of transmission media. A new group, the Transmission group, is allocated for this purpose: transmission OBJECT IDENTIFIER ::= { mib-2 10 } When Internet-standard definitions for managing transmission media are defined, the transmission group is used to provide a prefix for the names of those objects. Typically, such definitions reside in the experimental portion of the MIB until they are "proven", then as a part of the Internet standardization process, the definitions are accordingly elevated and a new object identifier, under the transmission group is defined. By convention, the name assigned is: type OBJECT IDENTIFIER ::= { transmission number } where "type" is the symbolic value used for the media in the ifType column of the ifTable object, and "number" is the actual integer value corresponding to the symbol. 3.12. The SNMP Group The application-oriented working groups of the IETF have been tasked to be receptive towards defining MIB variables specific to their respective applications. For the SNMP, it is useful to have statistical information. A new group, the SNMP group, is allocated for this purpose: snmp OBJECT IDENTIFIER ::= { mib-2 11 } 4. Objects Managed objects are accessed via a virtual information store, termed IETF SNMP Working Group [Page 8] RFC 1158 MIB II May 1990 the Management Information Base or MIB. Objects in the MIB are defined using Abstract Syntax Notation One (ASN.1) [9]. The mechanisms used for describing these objects are specified the companion memo, the SMI. In particular, each object has a name, a syntax, and an encoding. The name is an object identifier, an administratively assigned name, which specifies an object type. The object type together with an object instance serves to uniquely identify a specific instantiation of the object. For human convenience, we often use a textual string, termed the OBJECT DESCRIPTOR, to also refer to the object type. The syntax of an object type defines the abstract data structure corresponding to that object type. The ASN.1 language is used for this purpose. However, the companion memo purposely restricts the ASN.1 constructs which may be used. These restrictions are explicitly made for simplicity. The encoding of an object type is simply how that object type is represented using the object type's syntax. Implicitly tied to the notion of an object type's syntax and encoding is how the object type is represented when being transmitted on the network. This memo specifies the use of the basic encoding rules (BER) of ASN.1 [10], subject to the additional requirements imposed by the SNMP [14]. 4.1. Object Groups Since this list of managed objects contains only the essential elements, there is no need to allow individual objects to be optional. Rather, the objects are arranged into the following groups: - System - Interfaces - Address Translation (deprecated) - IP - ICMP - TCP - UDP - EGP - Transmission - SNMP There are two reasons for defining these groups: to provide a means of assigning object identifiers; and, to provide a method for implementations of managed agents to know which objects they must implement. This method is as follows: if the semantics of a group is applicable to an implementation, then it must implement all objects IETF SNMP Working Group [Page 9] RFC 1158 MIB II May 1990 in that group. For example, an implementation must implement the EGP group if and only if it implements the EGP. 4.2. Format of Definitions The next section contains the specification of all object types contained in the MIB. Following the conventions of the companion memo, the object types are defined using the following fields: OBJECT: ------- A textual name, termed the OBJECT DESCRIPTOR, for the object type, along with its corresponding OBJECT IDENTIFIER. Syntax: The abstract syntax for the object type, presented using ASN.1. This must resolve to an instance of the ASN.1 type ObjectSyntax defined in the SMI. Definition: A textual description of the semantics of the object type. Implementations should ensure that their interpretation of the object type fulfills this definition since this MIB is intended for use in multi- vendor environments. As such it is vital that object types have consistent meaning across all machines. Access: A keyword, one of read-only, read-write, write-only, or not-accessible. Note that this designation specifies the minimum level of support required. As a local matter, implementations may support other access types (e.g., an implementation may elect to permitting writing a variable marked herein as read-only). Further, protocol-specific "views" (e.g., those implied by an SNMP community) may make further restrictions on access to a variable. Status: A keyword, one of mandatory, optional, obsolete, or deprecated. Use of deprecated implies mandatory status. 5. Object Definitions RFC1158-MIB DEFINITIONS ::= BEGIN IETF SNMP Working Group [Page 10] RFC 1158 MIB II May 1990 IMPORTS mgmt, OBJECT-TYPE, NetworkAddress, IpAddress, Counter, Gauge, TimeTicks FROM RFC1155-SMI; DisplayString ::= OCTET STRING mib-2 OBJECT IDENTIFIER ::= { mgmt 1 } -- MIB-II system OBJECT IDENTIFIER ::= { mib-2 1 } interfaces OBJECT IDENTIFIER ::= { mib-2 2 } at OBJECT IDENTIFIER ::= { mib-2 3 } ip OBJECT IDENTIFIER ::= { mib-2 4 } icmp OBJECT IDENTIFIER ::= { mib-2 5 } tcp OBJECT IDENTIFIER ::= { mib-2 6 } udp OBJECT IDENTIFIER ::= { mib-2 7 } egp OBJECT IDENTIFIER ::= { mib-2 8 } -- cmot OBJECT IDENTIFIER ::= { mib-2 9 } transmission OBJECT IDENTIFIER ::= { mib-2 10 } snmp OBJECT IDENTIFIER ::= { mib-2 11 } END 5.1. The System Group Implementation of the System group is mandatory for all systems. OBJECT: ------- sysDescr { system 1 } Syntax: DisplayString (SIZE (0..255)) Definition: A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 11] RFC 1158 MIB II May 1990 OBJECT: ------- sysObjectID { system 2 } Syntax: OBJECT IDENTIFIER Definition: The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining "what kind of box" is being managed. For example, if vendor "Flintstones, Inc." was assigned the subtree 1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its "Fred Router". Access: read-only. Status: mandatory. OBJECT: ------- sysUpTime { system 3 } Syntax: TimeTicks Definition: The time (in hundredths of a second) since the network management portion of the system was last re-initialized. Access: read-only. Status: mandatory. OBJECT: ------- sysContact { system 4 } Syntax: DisplayString (SIZE (0..255)) IETF SNMP Working Group [Page 12] RFC 1158 MIB II May 1990 Definition: The textual identification of the contact person for this managed node, together with information on how to contact this person. Access: read-write. Status: mandatory. OBJECT: ------- sysName { system 5 } Syntax: DisplayString (SIZE (0..255)) Definition: An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name. Access: read-write. Status: mandatory. OBJECT: ------- sysLocation { system 6 } Syntax: DisplayString (SIZE (0..255)) Definition: The physical location of this node (e.g., "telephone closet, 3rd floor"). Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 13] RFC 1158 MIB II May 1990 OBJECT: ------- sysServices { system 7 } Syntax: INTEGER (0..127) Definition: A value which indicates the set of services that this entity potentially offers. The value is a sum. This sum initially takes the value zero, Then, for each layer, L, in the range 1 through 7, that this node performs transactions for, 2 raised to (L - 1) is added to the sum. For example, a node which performs only routing functions would have a value of 4 (2^(3-1)). In contrast, a node which is a host offering application services would have a value of 72 (2^(4-1) + 2^(7-1)). Note that in the context of the Internet suite of protocols, values should be calculated accordingly: layer functionality 1 physical (e.g., repeaters) 2 datalink/subnetwork (e.g., bridges) 3 internet (e.g., supports the IP) 4 end-to-end (e.g., supports the TCP) 7 applications (e.g., supports the SMTP) For systems including OSI protocols, layers 5 and 6 may also be counted. Access: read-only. Status: mandatory. 5.2. The Interfaces Group Implementation of the Interfaces group is mandatory for all systems. OBJECT: ------- ifNumber { interfaces 1 } Syntax: INTEGER IETF SNMP Working Group [Page 14] RFC 1158 MIB II May 1990 Definition: The number of network interfaces (regardless of their current state) present on this system. Access: read-only. Status: mandatory. 5.2.1. The Interfaces table The Interfaces table contains information on the entity's interfaces. Each interface is thought of as being attached to a "subnetwork". Note that this term should not be confused with "subnet" which refers to an addressing partitioning scheme used in the Internet suite of protocols. OBJECT: ------- ifTable { interfaces 2 } Syntax: SEQUENCE OF IfEntry Definition: A list of interface entries. The number of entries is given by the value of ifNumber. Access: read-only. Status: mandatory. OBJECT: ------- ifEntry { ifTable 1 } IETF SNMP Working Group [Page 15] RFC 1158 MIB II May 1990 Syntax: IfEntry ::= SEQUENCE { ifIndex INTEGER, ifDescr DisplayString, ifType INTEGER, ifMtu INTEGER, ifSpeed Gauge, ifPhysAddress OCTET STRING, ifAdminStatus INTEGER, ifOperStatus INTEGER, ifLastChange TimeTicks, ifInOctets Counter, ifInUcastPkts Counter, ifInNUcastPkts Counter, ifInDiscards Counter, ifInErrors Counter, ifInUnknownProtos Counter, ifOutOctets Counter, ifOutUcastPkts Counter, ifOutNUcastPkts Counter, ifOutDiscards Counter, ifOutErrors Counter, ifOutQLen Gauge, ifSpecific OBJECT IDENTIFIER } IETF SNMP Working Group [Page 16] RFC 1158 MIB II May 1990 Definition: An interface entry containing objects at the subnetwork layer and below for a particular interface. Access: read-only. Status: mandatory. We now consider the individual components of each interface entry: OBJECT: ------- ifIndex { ifEntry 1 } Syntax: INTEGER Definition: A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re- initialization of the entity's network management system to the next re-initialization. Access: read-only. Status: mandatory. OBJECT: ------- ifDescr { ifEntry 2 } Syntax: DisplayString (SIZE (0..255)) Definition: A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the hardware interface. IETF SNMP Working Group [Page 17] RFC 1158 MIB II May 1990 Access: read-only. Status: mandatory. OBJECT: ------- ifType { ifEntry 3 } Syntax: INTEGER { other(1), -- none of the following regular1822(2), hdh1822(3), ddn-x25(4), rfc877-x25(5), ethernet-csmacd(6), iso88023-csmacd(7), iso88024-tokenBus(8), iso88025-tokenRing(9), iso88026-man(10), starLan(11), proteon-10Mbit(12), proteon-80Mbit(13), hyperchannel(14), fddi(15), lapb(16), sdlc(17), t1-carrier(18), cept(19), -- european equivalent of T-1 basicISDN(20), primaryISDN(21), -- proprietary serial propPointToPointSerial(22), ppp(23), softwareLoopback(24), eon(25), -- CLNP over IP [12] ethernet-3Mbit(26) nsip(27), -- XNS over IP slip(28) -- generic SLIP } Definition: The type of interface, distinguished according to the physical/link protocol(s) immediately "below" the network layer in the protocol stack. IETF SNMP Working Group [Page 18] RFC 1158 MIB II May 1990 Access: read-only. Status: mandatory. OBJECT: ------- ifMtu { ifEntry 4 } Syntax: INTEGER Definition: The size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface. Access: read-only. Status: mandatory. OBJECT: ------- ifSpeed { ifEntry 5 } Syntax: Gauge Definition: An estimate of the interface's current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 19] RFC 1158 MIB II May 1990 OBJECT: ------- ifPhysAddress { ifEntry 6 } Syntax: OCTET STRING Definition: The interface's address at the protocol layer immediately "below" the network layer in the protocol stack. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length. Access: read-only. Status: mandatory. OBJECT: ------- ifAdminStatus { ifEntry 7 } Syntax: INTEGER { up(1), -- ready to pass packets down(2), testing(3) -- in some test mode } Definition: The desired state of the interface. The testing(3) state indicates that no operational packets can be passed. Access: read-write. Status: mandatory. OBJECT: ------- ifOperStatus { ifEntry 8 } IETF SNMP Working Group [Page 20] RFC 1158 MIB II May 1990 Syntax: INTEGER { up(1), -- ready to pass packets down(2), testing(3) -- in some test mode } Definition: The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. Access: read-only. Status: mandatory. OBJECT: ------- ifLastChange { ifEntry 9 } Syntax: TimeTicks Definition: The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value. Access: read-only. Status: mandatory. OBJECT: ------- ifInOctets { ifEntry 10 } Syntax: Counter IETF SNMP Working Group [Page 21] RFC 1158 MIB II May 1990 Definition: The total number of octets received on the interface, including framing characters. Access: read-only. Status: mandatory. OBJECT: ------- ifInUcastPkts { ifEntry 11 } Syntax: Counter Definition: The number of subnetwork-unicast packets delivered to a higher-layer protocol. Access: read-only. Status: mandatory. OBJECT: ------- ifInNUcastPkts { ifEntry 12 } Syntax: Counter Definition: The number of non-unicast (i.e., subnetwork-broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 22] RFC 1158 MIB II May 1990 OBJECT: ------- ifInDiscards { ifEntry 13 } Syntax: Counter Definition: The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. Access: read-only. Status: mandatory. OBJECT: ------- ifInErrors { ifEntry 14 } Syntax: Counter Definition: The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. Access: read-only. Status: mandatory. OBJECT: ------- ifInUnknownProtos { ifEntry 15 } Syntax: Counter IETF SNMP Working Group [Page 23] RFC 1158 MIB II May 1990 Definition: The number of packets received via the interface which were discarded because of an unknown or unsupported protocol. Access: read-only. Status: mandatory. OBJECT: ------- ifOutOctets { ifEntry 16 } Syntax: Counter Definition: The total number of octets transmitted out of the interface, including framing characters. Access: read-only. Status: mandatory. OBJECT: ------- ifOutUcastPkts { ifEntry 17 } Syntax: Counter Definition: The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 24] RFC 1158 MIB II May 1990 OBJECT: ------- ifOutNUcastPkts { ifEntry 18 } Syntax: Counter Definition: The total number of packets that higher-level protocols requested be transmitted to a non-unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent. Access: read-only. Status: mandatory. OBJECT: ------- ifOutDiscards { ifEntry 19 } Syntax: Counter Definition: The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. Access: read-only. Status: mandatory. OBJECT: ------- ifOutErrors { ifEntry 20 } Syntax: Counter IETF SNMP Working Group [Page 25] RFC 1158 MIB II May 1990 Definition: The number of outbound packets that could not be transmitted because of errors. Access: read-only. Status: mandatory. OBJECT: ------- ifOutQLen { ifEntry 21 } Syntax: Gauge Definition: The length of the output packet queue (in packets). Access: read-only. Status: mandatory. OBJECT: ------- ifSpecific { ifEntry 22 } Syntax: OBJECT IDENTIFIER Definition: A reference to MIB definitions specific to the particular media being used to realize the interface. For example, if the interface is realized by an ethernet, then the value of this object refers to a document defining objects specific to ethernet. If an agent is not configured to have a value for any of these variables, the object identifier nullSpecific OBJECT IDENTIFIER ::= { 0 0 } is returned. Note that "nullSpecific" is a syntatically valid object identifier, and any conformant IETF SNMP Working Group [Page 26] RFC 1158 MIB II May 1990 implementation of ASN.1 and BER must be able to generate and recognize this value. Access: read-only. Status: mandatory. 5.3. The Address Translation Group Implementation of the Address Translation group is mandatory for all systems. Note however that this group is deprecated by MIB-II. That is, it is being included solely for compatibility with MIB-I nodes, and will most likely be excluded from MIB-III nodes. From MIB-II and onwards, each network protocol group contains its own address translation tables. The Address Translation group contains one table which is the union across all interfaces of the translation tables for converting a NetworkAddress (e.g., an IP address) into a subnetwork-specific address. For lack of a better term, this document refers to such a subnetwork-specific address as a "physical" address. Examples of such translation tables are: for broadcast media where ARP is in use, the translation table is equivalent to the ARP cache; or, on an X.25 network where non-algorithmic translation to X.121 addresses is required, the translation table contains the NetworkAddress to X.121 address equivalences. OBJECT: ------- atTable { at 1 } Syntax: SEQUENCE OF AtEntry Definition: The Address Translation tables contain the NetworkAddress to "physical" address equivalences. Some interfaces do not use translation tables for determining address equivalences (e.g., DDN-X.25 has an algorithmic method); if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries. Access: read-write. IETF SNMP Working Group [Page 27] RFC 1158 MIB II May 1990 Status: deprecated. OBJECT: ------- atEntry { atTable 1 } Syntax: AtEntry ::= SEQUENCE { atIfIndex INTEGER, atPhysAddress OCTET STRING, atNetAddress NetworkAddress } Definition: Each entry contains one NetworkAddress to "physical" address equivalence. Access: read-write. Status: deprecated. We now consider the individual components of each Address Translation table entry: OBJECT: ------- atIfIndex { atEntry 1 } Syntax: INTEGER Definition: The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. Access: read-write. IETF SNMP Working Group [Page 28] RFC 1158 MIB II May 1990 Status: deprecated. OBJECT: ------- atPhysAddress { atEntry 2 } Syntax: OCTET STRING Definition: The media-dependent "physical" address. Setting this object to a null string (one of zero length) has the effect of invaliding the corresponding entry in the atTable object. That is, it effectively disassociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant atPhysAddress object. Access: read-write. Status: deprecated. OBJECT: ------- atNetAddress { atEntry 3 } Syntax: NetworkAddress Definition: The NetworkAddress (e.g., the IP address) corresponding to the media-dependent "physical" address. Access: read-write. IETF SNMP Working Group [Page 29] RFC 1158 MIB II May 1990 Status: deprecated. 5.4. The IP Group Implementation of the IP group is mandatory for all systems. OBJECT: ------- ipForwarding { ip 1 } Syntax: INTEGER { forwarding(1), -- i.e., acting as a gateway not-forwarding(2) -- i.e., NOT acting as a gateway } Definition: The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Access: read-write. Status: mandatory. OBJECT: ------- ipDefaultTTL { ip 2 } Syntax: INTEGER Definition: The default value inserted into the Time-To-Live field of the IP header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol. Access: read-write. IETF SNMP Working Group [Page 30] RFC 1158 MIB II May 1990 Status: mandatory. OBJECT: ------- ipInReceives { ip 3 } Syntax: Counter Definition: The total number of input datagrams received from interfaces, including those received in error. Access: read-only. Status: mandatory. OBJECT: ------- ipInHdrErrors { ip 4 } Syntax: Counter Definition: The number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, etc. Access: read-only. Status: mandatory. OBJECT: ------- ipInAddrErrors { ip 5 } Syntax: Counter IETF SNMP Working Group [Page 31] RFC 1158 MIB II May 1990 Definition: The number of input datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0.0.0) and addresses of unsupported Classes (e.g., Class E). For entities which are not IP Gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address. Access: read-only. Status: mandatory. OBJECT: ------- ipForwDatagrams { ip 6 } Syntax: Counter Definition: The number of input datagrams for which this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as IP Gateways, this counter will include only those packets which were Source-Routed via this entity, and the Source-Route option processing was successful. Access: read-only. Status: mandatory. OBJECT: ------- ipInUnknownProtos { ip 7 } Syntax: Counter IETF SNMP Working Group [Page 32] RFC 1158 MIB II May 1990 Definition: The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol. Access: read-only. Status: mandatory. OBJECT: ------- ipInDiscards { ip 8 } Syntax: Counter Definition: The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly. Access: read-only. Status: mandatory. OBJECT: ------- ipInDelivers { ip 9 } Syntax: Counter Definition: The total number of input datagrams successfully delivered to IP user-protocols (including ICMP). Access: read-only. IETF SNMP Working Group [Page 33] RFC 1158 MIB II May 1990 Status: mandatory. OBJECT: ------- ipOutRequests { ip 10 } Syntax: Counter Definition: The total number of IP datagrams which local IP user- protocols (including ICMP) supplied to IP in requests for transmission. Note that this counter does not include any datagrams counted in ipForwDatagrams. Access: read-only. Status: mandatory. OBJECT: ipOutDiscards { ip 11 } Syntax: Counter Definition: The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion. Access: read-only. Status: mandatory. OBJECT: ------- ipOutNoRoutes { ip 12 } IETF SNMP Working Group [Page 34] RFC 1158 MIB II May 1990 Syntax: Counter Definition: The number of IP datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this "no-route" criterion. Note that this includes any datagarms which a host cannot route because all of its default gateways are down. Access: read-only. Status: mandatory. OBJECT: ------- ipReasmTimeout { ip 13 } Syntax: INTEGER Definition: The maximum number of seconds which received fragments are held while they are awaiting reassembly at this entity. Access: read-only. Status: mandatory. OBJECT: ------- ipReasmReqds { ip 14 } Syntax: Counter Definition: The number of IP fragments received which needed to be reassembled at this entity. IETF SNMP Working Group [Page 35] RFC 1158 MIB II May 1990 Access: read-only. Status: mandatory. OBJECT: ------- ipReasmOKs { ip 15 } Syntax: Counter Definition: The number of IP datagrams successfully re-assembled. Access: read-only. Status: mandatory. OBJECT: ------- ipReasmFails { ip 16 } Syntax: Counter Definition: The number of failures detected by the IP re-assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of discarded IP fragments since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by combining them as they are received. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 36] RFC 1158 MIB II May 1990 OBJECT: ------- ipFragOKs { ip 17 } Syntax: Counter Definition: The number of IP datagrams that have been successfully fragmented at this entity. Access: read-only. Status: mandatory. OBJECT: ------- ipFragFails { ip 18 } Syntax: Counter Definition: The number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.g., because their "Don't Fragment" flag was set. Access: read-only. Status: mandatory. OBJECT: ------- ipFragCreates { ip 19 } Syntax: Counter Definition: The number of IP datagram fragments that have been generated as a result of fragmentation at this entity. IETF SNMP Working Group [Page 37] RFC 1158 MIB II May 1990 Access: read-only. Status: mandatory. 5.4.1. The IP Address table The Ip Address table contains this entity's IP addressing information. OBJECT: ------- ipAddrTable { ip 20 } Syntax: SEQUENCE OF IpAddrEntry Definition: The table of addressing information relevant to this entity's IP addresses. Access: read-only. Status: mandatory. OBJECT: ------- ipAddrEntry { ipAddrTable 1 } Syntax: IpAddrEntry ::= SEQUENCE { ipAdEntAddr IpAddress, ipAdEntIfIndex INTEGER, ipAdEntNetMask IpAddress, ipAdEntBcastAddr INTEGER, ipAdEntReasmMaxSize INTEGER (0..65535) } IETF SNMP Working Group [Page 38] RFC 1158 MIB II May 1990 Definition: The addressing information for one of this entity's IP addresses. Access: read-only. Status: mandatory. OBJECT: ------- ipAdEntAddr { ipAddrEntry 1 } Syntax: IpAddress Definition: The IP address to which this entry's addressing information pertains. Access: read-only. Status: mandatory. OBJECT: ------- ipAdEntIfIndex { ipAddrEntry 2 } Syntax: INTEGER Definition: The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 39] RFC 1158 MIB II May 1990 OBJECT: ------- ipAdEntNetMask { ipAddrEntry 3 } Syntax: IpAddress Definition: The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0. Access: read-only. Status: mandatory. OBJECT: ------- ipAdEntBcastAddr { ipAddrEntry 4 } Syntax: INTEGER Definition: The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface. Access: read-only. Status: mandatory. OBJECT: ------- ipAdEntReasmMaxSize { ipAddrEntry 5 } IETF SNMP Working Group [Page 40] RFC 1158 MIB II May 1990 Syntax: INTEGER (0..65535) Definition: The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface. Access: read-only. Status: mandatory. 5.4.2. The IP Routing table The IP Routing table contains an entry for each route presently known to this entity. OBJECT: ------- ipRoutingTable { ip 21 } Syntax: SEQUENCE OF IpRouteEntry Definition: This entity's IP Routing table. Access: read-write. Status: mandatory. OBJECT: ------- ipRouteEntry { ipRoutingTable 1 } Syntax: IpRouteEntry ::= SEQUENCE { ipRouteDest IpAddress, ipRouteIfIndex INTEGER, ipRouteMetric1 IETF SNMP Working Group [Page 41] RFC 1158 MIB II May 1990 INTEGER, ipRouteMetric2 INTEGER, ipRouteMetric3 INTEGER, ipRouteMetric4 INTEGER, ipRouteNextHop IpAddress, ipRouteType INTEGER, ipRouteProto INTEGER, ipRouteAge INTEGER, ipRouteMask IpAddress } Definition: A route to a particular destination. Access: read-write. Status: mandatory. We now consider the individual components of each route in the IP Routing table: OBJECT: ------- ipRouteDest { ipRouteEntry 1 } Syntax: IpAddress Definition: The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table-access mechanisms defined by the network management protocol in use. IETF SNMP Working Group [Page 42] RFC 1158 MIB II May 1990 Access: read-write. Status: mandatory. OBJECT: ------- ipRouteIfIndex { ipRouteEntry 2 } Syntax: INTEGER Definition: The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. Access: read-write. Status: mandatory. OBJECT: ------- ipRouteMetric1 { ipRouteEntry 3 } Syntax: INTEGER Definition: The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1. Access: read-write. Status: mandatory. IETF SNMP Working Group [Page 43] RFC 1158 MIB II May 1990 OBJECT: ------- ipRouteMetric2 { ipRouteEntry 4 } Syntax: INTEGER Definition: An alternate routing metric for this route. The semantics of this metric are determined by the routing- protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1. Access: read-write. Status: mandatory. OBJECT: ------- ipRouteMetric3 { ipRouteEntry 5 } Syntax: INTEGER Definition: An alternate routing metric for this route. The semantics of this metric are determined by the routing- protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1. Access: read-write. Status: mandatory. OBJECT: ------- ipRouteMetric4 { ipRouteEntry 6 } Syntax: INTEGER IETF SNMP Working Group [Page 44] RFC 1158 MIB II May 1990 Definition: An alternate routing metric for this route. The semantics of this metric are determined by the routing- protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1. Access: read-write. Status: mandatory. OBJECT: ------- ipRouteNextHop { ipRouteEntry 7 } Syntax: IpAddress Definition: The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.) Access: read-write. Status: mandatory. OBJECT: ------- ipRouteType { ipRouteEntry 8 } Syntax: INTEGER { other(1), -- none of the following invalid(2), -- an invalidated route -- route to directly direct(3), -- connected (sub-)network -- route to a non-local remote(4) -- host/network/sub-network IETF SNMP Working Group [Page 45] RFC 1158 MIB II May 1990 } Definition: The type of route. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipRoutingTable object. That is, it effectively disassociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object. Access: read-write. Status: mandatory. OBJECT: ------- ipRouteProto { ipRouteEntry 9 } Syntax: INTEGER { other(1), -- none of the following -- non-protocol information, -- e.g., manually configured local(2), -- entries -- set via a network management netmgmt(3), -- protocol -- obtained via ICMP, icmp(4), -- e.g., Redirect -- the remaining values are -- all gateway routing protocols egp(5), ggp(6), hello(7), rip(8), is-is(9), IETF SNMP Working Group [Page 46] RFC 1158 MIB II May 1990 es-is(10), ciscoIgrp(11), bbnSpfIgp(12), ospf(13), bgp(14) } Definition: The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols. Access: read-only. Status: mandatory. OBJECT: ------- ipRouteAge { ipRouteEntry 10 } Syntax: INTEGER Definition: The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of "too old" can be implied except through knowledge of the routing protocol by which the route was learned. Access: read-write. Status: mandatory. OBJECT: ------- ipRouteMask { ipRouteEntry 11 } Syntax: IpAddress IETF SNMP Working Group [Page 47] RFC 1158 MIB II May 1990 Definition: Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism. Access: read-write. Status: mandatory. 5.4.3. The IP Address Translation table The Address Translation tables contain the IpAddress to "physical" address equivalences. Some interfaces do not use translation tables for determining address equivalences (e.g., DDN-X.25 has an algorithmic method); if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries. OBJECT: ------- ipNetToMediaTable { ip 22 } Syntax: SEQUENCE OF IpNetToMediaEntry Definition: The IP Address Translation table used for mapping from IP addresses to physical addresses. Access: read-write. IETF SNMP Working Group [Page 48] RFC 1158 MIB II May 1990 Status: mandatory. OBJECT: ------- IpNetToMediaEntry { ipNetToMediaTable 1 } Syntax: IpNetToMediaEntry ::= SEQUENCE { ipNetToMediaIfIndex INTEGER, ipNetToMediaPhysAddress OCTET STRING, ipNetToMediaNetAddress IpAddress, ipNetToMediaType INTEGER } Definition: Each entry contains one IpAddress to "physical" address equivalence. Access: read-write. Status: mandatory. We now consider the individual components of each IP Address Translation table entry: OBJECT: ------- ipNetToMediaIfIndex { ipNetToMediaEntry 1 } Syntax: INTEGER Definition: The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. IETF SNMP Working Group [Page 49] RFC 1158 MIB II May 1990 Access: read-write. Status: mandatory. OBJECT: ------- ipNetToMediaPhysAddress { ipNetToMediaEntry 2 } Syntax: OCTET STRING Definition: The media-dependent "physical" address. Access: read-write. Status: mandatory. OBJECT: ------- ipNetToMediaNetAddress { ipNetToMediaEntry 3 } Syntax: IpAddress Definition: The IpAddress corresponding to the media-dependent "physical" address. Access: read-write. Status: mandatory. OBJECT: ------- ipNetToMediaType { ipNetToMediaEntry 4 } Syntax: INTEGER { IETF SNMP Working Group [Page 50] RFC 1158 MIB II May 1990 other(1), -- none of the following invalid(2), -- an invalidated mapping dynamic(3), static(4) } Definition: The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipNetToMediaTable. That is, it effectively disassociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipNetToMediaType object. Access: read-write. Status: mandatory. 5.5. The ICMP Group Implementation of the ICMP group is mandatory for all systems. The ICMP group contains the ICMP input and output statistics. OBJECT: ------- icmpInMsgs { icmp 1 } Syntax: Counter Definition: The total number of ICMP messages which the entity received. Note that this counter includes all those counted by icmpInErrors. IETF SNMP Working Group [Page 51] RFC 1158 MIB II May 1990 Access: read-only. Status: mandatory. OBJECT: ------- icmpInErrors { icmp 2 } Syntax: Counter Definition: The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.). Access: read-only. Status: mandatory. OBJECT: ------- icmpInDestUnreachs { icmp 3 } Syntax: Counter Definition: The number of ICMP Destination Unreachable messages received. Access: read-only. Status: mandatory. OBJECT: ------- icmpInTimeExcds { icmp 4 } IETF SNMP Working Group [Page 52] RFC 1158 MIB II May 1990 Syntax: Counter Definition: The number of ICMP Time Exceeded messages received. Access: read-only. Status: mandatory. OBJECT: ------- icmpInParmProbs { icmp 5 } Syntax: Counter Definition: The number of ICMP Parameter Problem messages received. Access: read-only. Status: mandatory. OBJECT: ------- icmpInSrcQuenchs { icmp 6 } Syntax: Counter Definition: The number of ICMP Source Quench messages received. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 53] RFC 1158 MIB II May 1990 OBJECT: ------- icmpInRedirects { icmp 7 } Syntax: Counter Definition: The number of ICMP Redirect messages received. Access: read-only. Status: mandatory. OBJECT: ------- icmpInEchos { icmp 8 } Syntax: Counter Definition: The number of ICMP Echo (request) messages received. Access: read-only. Status: mandatory. OBJECT: ------- icmpInEchoReps { icmp 9 } Syntax: Counter Definition: The number of ICMP Echo Reply messages received. Access: read-only. IETF SNMP Working Group [Page 54] RFC 1158 MIB II May 1990 Status: mandatory. OBJECT: ------- icmpInTimestamps { icmp 10 } Syntax: Counter Definition: The number of ICMP Timestamp (request) messages received. Access: read-only. Status: mandatory. OBJECT: ------- icmpInTimestampReps { icmp 11 } Syntax: Counter Definition: The number of ICMP Timestamp Reply messages received. Access: read-only. Status: mandatory. OBJECT: ------- icmpInAddrMasks { icmp 12 } Syntax: Counter Definition: The number of ICMP Address Mask Request messages received. IETF SNMP Working Group [Page 55] RFC 1158 MIB II May 1990 Access: read-only. Status: mandatory. OBJECT: ------- icmpInAddrMaskReps { icmp 13 } Syntax: Counter Definition: The number of ICMP Address Mask Reply messages received. Access: read-only. Status: mandatory. OBJECT: ------- icmpOutMsgs { icmp 14 } Syntax: Counter Definition: The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by icmpOutErrors. Access: read-only. Status: mandatory. OBJECT: ------- icmpOutErrors { icmp 15 } IETF SNMP Working Group [Page 56] RFC 1158 MIB II May 1990 Syntax: Counter Definition: The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value. Access: read-only. Status: mandatory. OBJECT: ------- icmpOutDestUnreachs { icmp 16 } Syntax: Counter Definition: The number of ICMP Destination Unreachable messages sent. Access: read-only. Status: mandatory. OBJECT: ------- icmpOutTimeExcds { icmp 17 } Syntax: Counter Definition: The number of ICMP Time Exceeded messages sent. Access: read-only. IETF SNMP Working Group [Page 57] RFC 1158 MIB II May 1990 Status: mandatory. OBJECT: ------- icmpOutParmProbs { icmp 18 } Syntax: Counter Definition: The number of ICMP Parameter Problem messages sent. Access: read-only. Status: mandatory. OBJECT: ------- icmpOutSrcQuenchs { icmp 19 } Syntax: Counter Definition: The number of ICMP Source Quench messages sent. Access: read-only. Status: mandatory. OBJECT: ------- icmpOutRedirects { icmp 20 } Syntax: Counter Definition: The number of ICMP Redirect messages sent. For a host, this object will always be zero, since hosts do not send IETF SNMP Working Group [Page 58] RFC 1158 MIB II May 1990 redirects. Access: read-only. Status: mandatory. OBJECT: ------- icmpOutEchos { icmp 21 } Syntax: Counter Definition: The number of ICMP Echo (request) messages sent. Access: read-only. Status: mandatory. OBJECT: ------- icmpOutEchoReps { icmp 22 } Syntax: Counter Definition: The number of ICMP Echo Reply messages sent. Access: read-only. Status: mandatory. OBJECT: ------- icmpOutTimestamps { icmp 23 } IETF SNMP Working Group [Page 59] RFC 1158 MIB II May 1990 Syntax: Counter Definition: The number of ICMP Timestamp (request) messages sent. Access: read-only. Status: mandatory. OBJECT: ------- icmpOutTimestampReps { icmp 24 } Syntax: Counter Definition: The number of ICMP Timestamp Reply messages sent. Access: read-only. Status: mandatory. OBJECT: ------- icmpOutAddrMasks { icmp 25 } Syntax: Counter Definition: The number of ICMP Address Mask Request messages sent. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 60] RFC 1158 MIB II May 1990 OBJECT: ------- icmpOutAddrMaskReps { icmp 26 } Syntax: Counter Definition: The number of ICMP Address Mask Reply messages sent. Access: read-only. Status: mandatory. 5.6. The TCP Group Implementation of the TCP group is mandatory for all systems that implement the TCP. Note that instances of object types that represent information about a particular TCP connection are transient; they persist only as long as the connection in question. OBJECT: ------- tcpRtoAlgorithm { tcp 1 } Syntax: INTEGER { other(1), -- none of the following constant(2), -- a constant rto rsre(3), -- MIL-STD-1778, Appendix B vanj(4) -- Van Jacobson's algorithm [11] } Definition: The algorithm used to determine the timeout value used for retransmitting unacknowledged octets. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 61] RFC 1158 MIB II May 1990 OBJECT: ------- tcpRtoMin { tcp 2 } Syntax: INTEGER Definition: The minimum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the LBOUND quantity described in RFC 793. Access: read-only. Status: mandatory. OBJECT: ------- tcpRtoMax { tcp 3 } Syntax: INTEGER Definition: The maximum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the UBOUND quantity described in RFC 793. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 62] RFC 1158 MIB II May 1990 OBJECT: ------- tcpMaxConn { tcp 4 } Syntax: INTEGER Definition: The limit on the total number of TCP connections the entity can support. In entities where the maximum number of connections is dynamic, this object should contain the value "-1". Access: read-only. Status: mandatory. OBJECT: ------- tcpActiveOpens { tcp 5 } Syntax: Counter Definition: The number of times TCP connections have made a direct transition to the SYN-SENT state from the CLOSED state. Access: read-only. Status: mandatory. OBJECT: ------- tcpPassiveOpens { tcp 6 } Syntax: Counter Definition: The number of times TCP connections have made a direct transition to the SYN-RCVD state from the LISTEN state. IETF SNMP Working Group [Page 63] RFC 1158 MIB II May 1990 Access: read-only. Status: mandatory. OBJECT: ------- tcpAttemptFails { tcp 7 } Syntax: Counter Definition: The number of times TCP connections have made a direct transition to the CLOSED state from either the SYN-SENT state or the SYN-RCVD state, plus the number of times TCP connections have made a direct transition to the LISTEN state from the SYN-RCVD state. Access: read-only. Status: mandatory. OBJECT: ------- tcpEstabResets { tcp 8 } Syntax: Counter Definition: The number of times TCP connections have made a direct transition to the CLOSED state from either the ESTABLISHED state or the CLOSE-WAIT state. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 64] RFC 1158 MIB II May 1990 OBJECT: ------- tcpCurrEstab { tcp 9 } Syntax: Gauge Definition: The number of TCP connections for which the current state is either ESTABLISHED or CLOSE-WAIT. Access: read-only. Status: mandatory. OBJECT: ------- tcpInSegs { tcp 10 } Syntax: Counter Definition: The total number of segments received, including those received in error. This count includes segments received on currently established connections. Access: read-only. Status: mandatory. OBJECT: ------- tcpOutSegs { tcp 11 } Syntax: Counter Definition: The total number of segments sent, including those on current connections but excluding those containing only retransmitted octets. IETF SNMP Working Group [Page 65] RFC 1158 MIB II May 1990 Access: read-only. Status: mandatory. OBJECT: ------- tcpRetransSegs { tcp 12 } Syntax: Counter Definition: The total number of segments retransmitted - that is, the number of TCP segments transmitted containing one or more previously transmitted octets. Access: read-only. Status: mandatory. 5.6.1. The TCP Connection table The TCP connection table contains information about this entity's existing TCP connections. OBJECT: ------- tcpConnTable { tcp 13 } Syntax: SEQUENCE OF TcpConnEntry Definition: A table containing TCP connection-specific information. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 66] RFC 1158 MIB II May 1990 OBJECT: ------- tcpConnEntry { tcpConnTable 1 } Syntax: TcpConnEntry ::= SEQUENCE { tcpConnState INTEGER, tcpConnLocalAddress IpAddress, tcpConnLocalPort INTEGER (0..65535), tcpConnRemAddress IpAddress, tcpConnRemPort INTEGER (0..65535) } Definition: Information about a particular current TCP connection. An object of this type is transient, in that it ceases to exist when (or soon after) the connection makes the transition to the CLOSED state. Access: read-only. Status: mandatory. OBJECT: ------- tcpConnState { tcpConnEntry 1 } Syntax: INTEGER { closed(1), listen(2), synSent(3), synReceived(4), established(5), finWait1(6), finWait2(7), closeWait(8), lastAck(9), closing(10), timeWait(11) IETF SNMP Working Group [Page 67] RFC 1158 MIB II May 1990 } Definition: The state of this TCP connection. Access: read-only. Status: mandatory. OBJECT: ------- tcpConnLocalAddress { tcpConnEntry 2 } Syntax: IpAddress Definition: The local IP address for this TCP connection. In the case of a connection in the listen state which is willing to accept connections for any IP interface associated with the node, the value 0.0.0.0 is used. Access: read-only. Status: mandatory. OBJECT: ------- tcpConnLocalPort { tcpConnEntry 3 } Syntax: INTEGER (0..65535) Definition: The local port number for this TCP connection. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 68] RFC 1158 MIB II May 1990 OBJECT: ------- tcpConnRemAddress { tcpConnEntry 4 } Syntax: IpAddress Definition: The remote IP address for this TCP connection. Access: read-only. Status: mandatory. OBJECT: ------- tcpConnRemPort { tcpConnEntry 5 } Syntax: INTEGER (0..65535) Definition: The remote port number for this TCP connection. Access: read-only. Status: mandatory. 5.6.2. Additional TCP Objects OBJECT: ------- tcpInErrs { tcp 14 } Syntax: Counter Definition: The total number of segments received in error (e.g., bad TCP checksums). IETF SNMP Working Group [Page 69] RFC 1158 MIB II May 1990 Access: read-only. Status: mandatory. OBJECT: ------- tcpOutRsts { tcp 15 } Syntax: Counter Definition: The number of TCP segments sent containing the RST flag. Access: read-only. Status: mandatory. 5.7. The UDP Group Implementation of the UDP group is mandatory for all systems which implement the UDP. OBJECT: ------- udpInDatagrams { udp 1 } Syntax: Counter Definition: The total number of UDP datagrams delivered to UDP users. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 70] RFC 1158 MIB II May 1990 OBJECT: ------- udpNoPorts { udp 2 } Syntax: Counter Definition: The total number of received UDP datagrams for which there was no application at the destination port. Access: read-only. Status: mandatory. OBJECT: ------- udpInErrors { udp 3 } Syntax: Counter Definition: The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port. Access: read-only. Status: mandatory. OBJECT: ------- udpOutDatagrams { udp 4 } Syntax: Counter Definition: The total number of UDP datagrams sent from this entity. IETF SNMP Working Group [Page 71] RFC 1158 MIB II May 1990 Access: read-only. Status: mandatory. 5.7.1. The UDP Listener table The UDP listener table contains information about this entity's UDP end-points on which a local application is currently accepting datagrams. OBJECT: ------- udpTable { udp 5 } Syntax: SEQUENCE OF UdpEntry Definition: A table containing UDP listener information. Access: read-only. Status: mandatory. OBJECT: ------- udpEntry { udpTable 1 } Syntax: UdpEntry ::= SEQUENCE { udpLocalAddress IpAddress, udpLocalPort INTEGER (0..65535) } Definition: Information about a particular current UDP listener. Access: read-only. IETF SNMP Working Group [Page 72] RFC 1158 MIB II May 1990 Status: mandatory. OBJECT: ------- udpLocalAddress { udpEntry 1 } Syntax: IpAddress Definition: The local IP address for this UDP listener. In the case of a UDP listener which is willing to accept datagrams for any IP interface associated with the node, the value 0.0.0.0 is used. Access: read-only. Status: mandatory. OBJECT: ------- udpLocalPort { udpEntry 2 } Syntax: INTEGER (0..65535) Definition: The local port number for this UDP listener. Access: read-only. Status: mandatory. 5.8. The EGP Group Implementation of the EGP group is mandatory for all systems which implement the EGP. IETF SNMP Working Group [Page 73] RFC 1158 MIB II May 1990 OBJECT: ------- egpInMsgs { egp 1 } Syntax: Counter Definition: The number of EGP messages received without error. Access: read-only. Status: mandatory. OBJECT: ------- egpInErrors { egp 2 } Syntax: Counter Definition: The number of EGP messages received that proved to be in error. Access: read-only. Status: mandatory. OBJECT: ------- egpOutMsgs { egp 3 } Syntax: Counter Definition: The total number of locally generated EGP messages. Access: read-only. IETF SNMP Working Group [Page 74] RFC 1158 MIB II May 1990 Status: mandatory. OBJECT: ------- egpOutErrors { egp 4 } Syntax: Counter Definition: The number of locally generated EGP messages not sent due to resource limitations within an EGP entity. Access: read-only. Status: mandatory. 5.8.1. The EGP Neighbor table The Egp Neighbor table contains information about this entity's EGP neighbors. OBJECT: ------- egpNeighTable { egp 5 } Syntax: SEQUENCE OF EgpNeighEntry Definition: The EGP neighbor table. Access: read-only. Status: mandatory. OBJECT: ------- egpNeighEntry { egpNeighTable 1 } IETF SNMP Working Group [Page 75] RFC 1158 MIB II May 1990 Syntax: EgpNeighEntry ::= SEQUENCE { egpNeighState INTEGER, egpNeighAddr IpAddress, egpNeighAs INTEGER, egpNeighInMsgs Counter, egpNeighInErrs Counter, egpNeighOutMsgs Counter, egpNeighOutErrs Counter, egpNeighInErrMsgs Counter, egpNeighOutErrMsgs Counter, egpNeighStateUps Counter, egpNeighStateDowns Counter, egpNeighIntervalHello INTEGER, egpNeighIntervalPoll INTEGER, egpNeighMode INTEGER, egpNeighEventTrigger INTEGER } Definition: Information about this entity's relationship with a particular EGP neighbor. Access: read-only. Status: mandatory. We now consider the individual components of each EGP neighbor entry: IETF SNMP Working Group [Page 76] RFC 1158 MIB II May 1990 OBJECT: ------- egpNeighState { egpNeighEntry 1 } Syntax: INTEGER { idle(1), acquisition(2), down(3), up(4), cease(5) } Definition: The EGP state of the local system with respect to this entry's EGP neighbor. Each EGP state is represented by a value that is one greater than the numerical value associated with said state in RFC 904. Access: read-only. Status: mandatory. OBJECT: ------- egpNeighAddr { egpNeighEntry 2 } Syntax: IpAddress Definition: The IP address of this entry's EGP neighbor. Access: read-only. Status: mandatory. OBJECT: ------- egpNeighAs { egpNeighEntry 3 } IETF SNMP Working Group [Page 77] RFC 1158 MIB II May 1990 Syntax: INTEGER Definition: The autonomous system of this EGP peer. Zero should be specified if the autonomous system number of the neighbor is not yet known. Access: read-only. Status: mandatory. OBJECT: ------- egpNeighInMsgs { egpNeighEntry 4 } Syntax: Counter Definition: The number of EGP messages received without error from this EGP peer. Access: read-only. Status: mandatory. OBJECT: ------- egpNeighInErrs { egpNeighEntry 5 } Syntax: Counter Definition: The number of EGP messages received from this EGP peer that proved to be in error (e.g., bad EGP checksum). Access: read-only. IETF SNMP Working Group [Page 78] RFC 1158 MIB II May 1990 Status: mandatory. OBJECT: ------- egpNeighOutMsgs { egpNeighEntry 6 } Syntax: Counter Definition: The number of locally generated EGP messages to this EGP peer. Access: read-only. Status: mandatory. OBJECT: ------- egpNeighOutErrs { egpNeighEntry 7 } Syntax: Counter Definition: The number of locally generated EGP messages not sent to this EGP peer due to resource limitations within an EGP entity. Access: read-only. Status: mandatory. OBJECT: ------- egpNeighInErrMsgs { egpNeighEntry 8 } Syntax: Counter IETF SNMP Working Group [Page 79] RFC 1158 MIB II May 1990 Definition: The number of EGP-defined error messages received from this EGP peer. Access: read-only. Status: mandatory. OBJECT: ------- egpNeighOutErrMsgs { egpNeighEntry 9 } Syntax: Counter Definition: The number of EGP-defined error messages sent to this EGP peer. Access: read-only. Status: mandatory. OBJECT: ------- egpNeighStateUps { egpNeighEntry 10 } Syntax: Counter Definition: The number of EGP state transitions to the UP state with this EGP peer. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 80] RFC 1158 MIB II May 1990 OBJECT: ------- egpNeighStateDowns { egpNeighEntry 11 } Syntax: Counter Definition: The number of EGP state transitions from the UP state to any other state with this EGP peer. Access: read-only. Status: mandatory. OBJECT: ------- egpNeighIntervalHello { egpNeighEntry 12 } Syntax: INTEGER Definition: The interval between EGP Hello command retransmissions (in hundredths of a second). This represents the t1 timer as defined in RFC 904. Access: read-only. Status: mandatory. OBJECT: ------- egpNeighIntervalPoll { egpNeighEntry 13 } Syntax: INTEGER Definition: The interval between EGP poll command retransmissions (in hundredths of a second). This represents the t3 timer as defined in RFC 904. IETF SNMP Working Group [Page 81] RFC 1158 MIB II May 1990 Access: read-only. Status: mandatory. OBJECT: ------- egpNeighMode { egpNeighEntry 14 } Syntax: INTEGER { active(1), passive(2) } Definition: The polling mode of this EGP entity, either passive or active. Access: read-only. Status: mandatory. OBJECT: ------- egpNeighEventTrigger { egpNeighEntry 15 } Syntax: INTEGER { start(1), stop(2) } Definition: A control variable used to trigger operator-initiated Start and Stop events. When read, this variable always returns the most recent value that egpNeightEventTrigger was set to. If it has not been set since the last initialization of the network management subsystem on the node, it returns a value of "stop". Access: read-write IETF SNMP Working Group [Page 82] RFC 1158 MIB II May 1990 Status: mandatory. 5.8.2. Additional EGP variables OBJECT: ------- egpAs { egp 6 } Syntax: INTEGER Definition: The autonomous system number of this EGP entity. Access: read-only. Status: mandatory. 5.9. The Transmission Group Based on the transmission media underlying each interface on a system, the corresponding portion of the Transmission group is mandatory for that system. When Internet-standard definitions for managing transmission media are defined, the transmission group is used to provide a prefix for the names of those objects. Typically, such definitions reside in the experimental portion of the MIB until they are "proven", then as a part of the Internet standardization process, the definitions are accordingly elevated and a new object identifier, under the transmission group is defined. By convention, the name assigned is: type OBJECT IDENTIFIER ::= { transmission number } where "type" is the symbolic value used for the media in the ifType column of the ifTable object, and "number" is the actual integer value corresponding to the symbol. 5.10. The SNMP Group Implementation of the SNMP group is mandatory for all systems which support an SNMP protocol entity. Some of the objects defined below IETF SNMP Working Group [Page 83] RFC 1158 MIB II May 1990 will be zero-valued in those SNMP implementations that are optimized to support only those functions specific to either a management agent or a management client. OBJECT: ------- snmpInPkts { snmp 1 } Syntax: Counter Definition: The total number of PDUs delivered to the SNMP entity from the transport service. Access: read-only. Status: mandatory. OBJECT: ------- snmpOutPkts { snmp 2 } Syntax: Counter Definition: The total number of SNMP PDUs which were passed from the SNMP protocol entity to the transport service. Access: read-only. Status: mandatory. OBJECT: ------- snmpInBadVersions { snmp 3 } Syntax: Counter IETF SNMP Working Group [Page 84] RFC 1158 MIB II May 1990 Definition: The total number of syntactically correct SNMP PDUs which were delivered to the SNMP protocol entity and were for an unsupported SNMP version. Access: read-only. Status: mandatory. OBJECT: ------- snmpInBadCommunityNames { snmp 4 } Syntax: Counter Definition: The total number of SNMP PDUs delivered to the SNMP protocol entity which used a SNMP community name not known to said entity. Access: read-only. Status: mandatory. OBJECT: ------- snmpInBadCommunityUses { snmp 5 } Syntax: Counter Definition: The total number of SNMP PDUs delivered to the SNMP protocol entity which represented an SNMP operation which was not allowed by the SNMP community named in the PDU. Access: read-only. Status: mandatory. IETF SNMP Working Group [Page 85] RFC 1158 MIB II May 1990 OBJECT: ------- snmpInASNParseErrs { snmp 6 } Syntax: Counter Definition: The total number of ASN.1 parsing errors (either in encoding or syntax) encountered by the SNMP protocol entity when decoding received SNMP PDUs. Access: read-only. Status: mandatory. OBJECT: ------- snmpInBadTypes { snmp 7 } Syntax: Counter Definition: The total number of SNMP PDUs delivered to the SNMP protocol entity which had an unknown PDU type. Access: read-only. Status: mandatory. OBJECT: ------- snmpInTooBigs { snmp 8 } Syntax: Counter Definition: The total number valid SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the "ErrorStatus" component is "tooBig." IETF SNMP Working Group [Page 86] RFC 1158 MIB II May 1990 Access: read-only. Status: mandatory. OBJECT: ------- snmpInNoSuchNames { snmp 9 } Syntax: Counter Definition: The total number valid SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the "ErrorStatus" component is "noSuchName." Access: read-only. Status: mandatory. OBJECT: ------- snmpInBadValues { snmp 10 } Syntax: Counter Definition: The total number valid SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the "ErrorStatus" component is "badValue." Access: read-only. Status: mandatory. OBJECT: ------- snmpInReadOnlys { snmp 11 } IETF SNMP Working Group [Page 87] RFC 1158 MIB II May 1990 Syntax: Counter Definition: The total number valid SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the "ErrorStatus" component is "readOnly." Access: read-only. Status: mandatory. OBJECT: ------- snmpInGenErrs { snmp 12 } Syntax: Counter Definition: The total number valid SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the "ErrorStatus" component is "genErr." Access: read-only. Status: mandatory. OBJECT: ------- snmpInTotalReqVars { snmp 13 } Syntax: Counter Definition: The total number of MIB objects which have been retrieved successfully by the SNMP protocol entity as the result of receiving valid SNMP Get-Request and Get-Next PDUs. Access: read-only. IETF SNMP Working Group [Page 88] RFC 1158 MIB II May 1990 Status: mandatory. OBJECT: ------- snmpInTotalSetVars { snmp 14 } Syntax: Counter Definition: The total number of MIB objects which have been altered successfully by the SNMP protocol entity as the result of receiving valid SNMP Set-Request PDUs. Access: read-only. Status: mandatory. OBJECT: ------- snmpInGetRequests { snmp 15 } Syntax: Counter Definition: The total number of SNMP Get-Request PDUs which have been accepted and processed by the SNMP protocol entity. Access: read-only. Status: mandatory.